High Quality V Mixer Machine

The labeling machine is a very important part of the production process. It is recommended that you understand the working process and precautions of the labeling machine.

An integral part of the labeling machine
The working process of the labeling machine
Points to note in the work process


1、An integral part of the labeling machineThe body of the labeling machine is roughly as follows, the important core control center PLC, electric eye, label winding mechanism, conveyor belt, label stripping mechanism and display screen.
PLC: It is mainly written by program, and the next step is made by sending out instructions by returning the detected signal.
Electric eye: In the labeling machine, there will be an electric eye for measuring objects and an electric eye for measuring labels. The easy-to-understand explanation of the electric eye for measuring objects is to detect the electronic eye that the labeling object has passed through. The standard measuring electric eye is to detect the label output and adjust the accuracy of labeling. Generally, after the object is detected and the signal is returned to the PLC, an instruction is given to pull the label out.
Display screen: It is an interface for man to operate, which is convenient to control the operation and stop instructions of the machine.
Conveyor belt: plays a role in automatically conveying products.
Label peeling mechanism: A mechanism that peels a single label from a roll label and then applies the label to an object.


2、The working process of the labeling machineThe working principle of the labeling machine is to feed the items into the machine on a conveyor at a constant speed. The mechanical fixing device separates the items by a fixed distance, and then pushes the items in the direction of the conveyor belt.
At the beginning, the boxes are fed to the machine at a constant speed on the conveyor belt. The mechanical fixing device separates the boxes by a fixed distance and pushes the boxes to it in the direction of the conveyor belt. The driving wheel intermittently drags the label tape to move, the label tape is pulled out from the reel, and the labeling wheel will press the label tape on the box through the labeling wheel. The label is attached to the box when the labeling wheel moves at the same speed as the box. When the conveyor belt reaches a certain position, the label belt drive wheel will accelerate to a speed matching the conveyor belt, and after the label is applied, it will decelerate to a stop.


3、Points to note in the work processTake protective measures
Hands, arms and other parts of the body must leave the working part of the labeling machine, and the body must not exceed the safety range. If there are special circumstances, such as maintenance or something, take protective measures.


Pay attention to the details of wearing
When operating the machine, you must be focused, the clothes must be suitable, and do not wear clothes with straps. And if it’s a girl, be careful with your hair.
Check the condition of each part in advance.
Before it works, it must be ensured that the correct raw materials are used and properly prepared. In addition, tighten the bolts, screws and every mechanical part, and check the environment of the labeling machine. There must be no flammable and explosive materials on site.


The above is some information shared by our company. If you want more detailed information, please inquire.

Many users may have many questions about how to install the bottle blowing machine after purchasing it. Now I can tell you about the basic requirements for the installation of the blow molding machine, the installation sequence, and the points that need attention.Let us know a lot at present.

Requirements for the installation foundation of the bottle blowing machine
Installation sequence of the blow molding machine
Precautions during installation


1. Requirements for the installation foundation of the bottle blowing machineFirst of all, the layout of the machine in the workshop should meet the convenience of mold replacement and maintenance. In other words, there must be enough space to meet the requirements of basic work activities. Secondly, in order to avoid vibration during work, the machine should be placed on a cement foundation. The thickness of the foundation, the concrete marking and the level error of the foundation should all be controlled within a reasonable range. Finally, the bearing capacity of the installation foundation shall not be less than the minimum value.


2. Installation sequence of theblow molding machineInstallation is mainly divided into fixed installation and mobile installation.
Fixed installation is to transport the machine to the foundation dug in advance, install the foundation screws, and lay the water, electricity and gas transmission pipelines. Preliminarily adjust the level, and then pour concrete into the anchor holes, and then fine-tune the level after the concrete is dry. The method of fine-adjusting the level is to use a level to measure on the upper plane of the lock template and the dovetail groove of the pen holder. After the vertical and horizontal level is adjusted, the anchor screws are evenly tightened. Finally, check the equipment level, center height and center line position of the bottle blowing machine, and tighten the bolt holes of each foot.
Mobile installation can move equipment at any time. Just place the anti-vibration pad on the empty position of the anchor bolt, use a level ruler on the upper edge of the template to correct the level, adjust the anti-vibration pad, and then tighten the nut. Finally, corresponding inspections must be carried out.


3. Precautions during installationWhen installing the bottle blowing machine, ensure that the axis position of the cylinder is consistent with the direction of movement.
The load on the bottle blowing machine should not be too large to avoid eccentricity.
The level of fine adjustment is required during the installation process, which requires the assistance of professionals. If you find any emergencies during the installation process, it is best to seek professional help.


With the continuous development of blow molding machine technology, in general, the operating steps of the blow molding machine have become relatively simple, but even if the installation process is not that complicated, the installation process must not be taken lightly and must be carried out strictly in accordance with the instructions. Install to avoid accidents.If you need anything help about blow molding machine,you can call us .

In the daily production work, the cleaning of the blow molding machine also plays a large role. How to clean quickly and efficiently has a certain effect on machine maintenance and later work.

Cleaning the blow molding machine
Cleaning tips
The benefits of cleaning


1、Cleaning the blow molding machineBlow molding machines have different parts, and the cleaning methods for different parts are definitely different. Cleaning the head is a very important step, and several methods are introduced next.
Manual cleaning. In order to avoid scratching the runner, especially the mold area, we have to use manual cleaning, especially for metallurgical damage.
Solvent cleaning. Use acidic or alkaline chemicals, or organic or inorganic solvents for cleaning. The former method is low in cost, but the cost of chemicals is high and the cleaning efficiency is low. The latter has higher cleaning efficiency.
Ultrasonic cleaning. This method has a good cleaning effect. Remove inorganic residues.


2、Cleaning tipsAs can be seen from the above, there are many ways to clean. Then let me tell you a few tips.
Ensure that the temperature controller of the machine is working properly and set to the specified temperature of the cleaning compound. Increasing the temperature of the nozzle or mold by 50ºF can improve the cleaning effect.
Set the die gap large enough to allow material to flow out when the nozzle is filled with cleaning agent. Restricting the mold gap during the purge will increase the back pressure of the nozzle, allowing more aggressive cleaning.
Reduce the extruder speed from the normal operating speed. At each restart, start the extruder at a speed of approximately 20% or less, and then slowly increase while monitoring the pressure indicator in all steps.
Depending on the age and condition of the machine before cleaning, it may be necessary to fill the cleaning compound more than once to reach a clean state. Pre-measure the standard volume and an additional barrel capacity so you have more free space and can repeat.


3、The benefits of cleaningReduce downtime and costs
If we can master effective cleaning methods and use them faster and better, the methods and methods will help reduce maintenance-related downtime even up to 90%, which will reduce our daily costs to a certain extent. Expand production efficiency and realize a virtuous circle.


Minimize waste and wear
Deposits and carbon deposits will increase maintenance and repair costs, while reducing the service life of screws, cylinders, tools and nozzles, or defective products due to material inclusions, discoloration or other contamination. Regular cleaning and maintenance will help reduce the consumption of raw materials and damage to the machine.


Quickly change colors and materials
The conversion of injection molding machines.
Such as small batch production or OEM production, is a big cost factor. The faster and more efficient form, color or material conversion, the production process will be more efficient.


In short, for blow molding machines. Daily cleaning is still very useful. Based on the above women, you can buy our products to get the best experience.

Efficient embryo supply system: The fully automated embryo trimming and loading mechanism not only realizes fast and efficient embryo trimming and loading, saving labor costs, but also further improves the stability of the entire equipment workflow. It is installed on the track of the embryo trimming mechanism. There is a sensor. When the preform is lacking in the embryo channel, the preform will automatically enter the embryo management system from the hopper, and the single-channel preform feeding is adopted, which effectively solves the problem of wear between the preform and the preform.


Servo de-dividing system: De-dividing adopts servo motor equidistant de-dividing. The stroke and speed of the servo motor are simple to adjust, and the parameters can be adjusted on the operating table. The complex process is completed by digitization, which is safe, fast and accurate. Compared with the traditional multi-channel demolition and cylinder decompression, the single-channel demultiplication method controlled by the servo motor is faster and the position is more accurate.


Intelligent heating system: The infrared lamp is used to penetrate the preform for heating, so that the preform can be stretched more evenly and has high transparency; imported reflective mirror aluminum plate is installed inside to make full use of the heat energy of the lamp, shorten the heating time, reduce energy consumption, and increase production capacity. And each lamp tube on each layer can adjust the temperature individually, and adjust up and down, back and forth according to the customer's different tube blanks. The intelligent ventilation system can fully keep the temperature inside the heating box constant.


Servo clamping system: The clamping system is driven by a servo motor and driven by a mechanical link. The mold and the bottom mold are synchronously clamped by a servo motor. The back of the mold base is equipped with a high-pressure booster plate and high-pressure mold clamping, which effectively reduces the visibility of the mold clamping line of the finished bottle and ensures the quality of the bottle. The mold adopts a drawer structure, which is easy to replace the mold, and the operator can complete it within half an hour.


Servo stretching system: The servo motor drives the stretching system, the servo motor drives the gear rack to stretch, and the self-developed photoelectric limit and mechanical limit double guarantee mode prevents the stretching rod from touching the bottom mold, and the cycle time of the first blow and the second blow All can be adjusted individually on the console. According to different preforms and different bottle types of customers, the stretching rod can be adjusted automatically, with high flexibility.


Human-machine operating system: Longxin blow molding machine has a high degree of intelligence and is simple and convenient to operate. It adopts Chinese and English color touch screen, has perfect monitoring and induction settings, and has functions such as fault diagnosis display, automatic calculation report, memory storage, etc., which can control the production status of the equipment at all times.


Cooling/chilled water circulation system: The cooling and heating head device independently developed by Longxin Company ensures the cooling of the heating head after the bottle is released. There is a cooling water channel under the heating box. When the preform is heated, the cooling water channel is used to block the heat of the lamp tube. There is a cold air system under the cooling water channel to cool the bottle mouth and protect the tooth mouth from deformation. Chilled water leads to the mold, which cools the mold quickly and improves the production efficiency of the whole machine.


Standardized parts and high-quality electrical components: Most of the components of Skytech adopt international production standards, and the standard parts are mass-produced in the CNC machining center of Skytech, and put into use after strict inspection by the quality inspection department. Standardized parts ensure the reliability and stability of the performance of the SKY blow molding machine and reduce maintenance costs. The key components of Sikai bottle blowing machine, such as motor, PLC, cylinder, solenoid valve, relay and air blowing valve, are all high-quality products from famous foreign manufacturers.

Automatic PET Bottle Blow Molding Machine
 Automatic blowing machine adopts our most advanced blowing technologies. This machine is a fully automatic,high intelligent,stable and reliable blowing machine,with simple structure,and low energy consumption.  It is very popular and well used in food ,beverages,cosmetics,pharmaceutical industry.

               Semi-Automatic PET Bottle Blow Molding Machine
The machine is also equipped with muffler and oiling system to lubricate the mechanical part of the machine.